6SE6440-2UD21-1AA1 MANUAL PDF

6SEUDAA1. –. –. – .. Instruction Manual for details. LC filter and sinusoidal .. General installation instructions. Availability of the. (n. di ordinazione 6SE . You will find the Operating Instructions on the Docu CD delivered with your inverter. If and Notes contained in these manuals. MICROMASTER kW – kW. Operating Instructions. Issue 12/ User Documentation. 6SEAWBP0.

Author: Akinom Nikokasa
Country: Sri Lanka
Language: English (Spanish)
Genre: Marketing
Published (Last): 21 February 2011
Pages: 500
PDF File Size: 20.73 Mb
ePub File Size: 18.28 Mb
ISBN: 931-3-35356-344-9
Downloads: 42753
Price: Free* [*Free Regsitration Required]
Uploader: Shahn

Page 42 Page 43 – Fig. Load Torque Monitoring This avoids erroneous alarms which could be caused by brief transient states 6se64440-2ud21-1aa1 to Fig.

Commissioning If a line supply failure interrupts commissioning, then inconsistencies can occur regarding the parameterization. All of the drives must be operated with closed-loop Vector speed control with or without speed actual value encoder The ramp-up and ramp-down times of the ramp-function generator must be identical for all of the drives. Essentially the same as the binectors, the connector inputs are characterized by a “P” parameter e. Jog In addition to the explicit parameterization P and Pthe JOG functionality is also enabled via parameter P or P implicit parameterization.

Frequently used states including the parameter 6se66440-2ud21-1aa1 and bit are shown in the following Table refer to Table 6se6440-2ud21-1az1 This setting should be changed if a maximum frequency of higher than 50 Hz is required. When this function is used within a control loop, this smoothing has a negative impact on the control behavior and immunity to noise the dynamic performance deteriorates. By pressing ‘print’ button you will print only current page. Page 6se6440-2ud21-1az1 Page 62 – Fig.

For further information about options, please refer to the catalog or the documentation CD. These values have default settings so that the “Fault and shutdown” thresholds do not respond.

Most Related  BUKU SINTONG PANJAITAN PDF

Siemens MICROMASTER 440 Operating Instructions Manual Page 10

This type of cascaded closed-loop control has proven itself in practice regarding commissioning and increased transparency.

To disengaged the release mechanism of the inverter, insert a screwdriver into the release mechanism.

It allows easy and efficient connection of the necessary screening. The motor moment of inertia P is directly calculated during the quick commissioning refer to Section 3. Vector Control The drive and braking torque are controlled independently of the speed Full holding torque is possible at 0 speed These advantages are, under certain circumstances, already achieved without using speed feedback.

The status is displayed using signal r bit DriveMonitor offer, in 6se6440-2ud21-1wa1 with the drive inverter, parameter-orientated quick commissioning where the user is navigated through the menu tree mentioned above.

You can re-establish the initial state at any time by carrying-out a parameter reset to the factory setting. Page – Table Current reduction depending on F, F 6we6440-2ud21-1aa1 chart number: By using indexing, several different settings can be saved for each parameter which can be activated by changing-over the data set i. Page 72 – Commissioning Page 73 – Fig.

P or 0 6sf6440-2ud21-1aa1 for the direction of rotation inhibit the setpoint speed for the control is obtained r If required, parameter changes must be made for motors from third-party manufacturers.

Page Page – Table Important parameters for the Therefore, they do not fall within the scope of the harmonics emissions specification EN This functionality can be used to advantage, especially for discontinuous processes.

Siemens MICROMASTER 440 Operating Instructions Manual

P “Holding brake release delay” refer to Fig. The drive and braking torque are controlled independently of the speed Full holding torque is possible at 0 speed These advantages are, under certain circumstances, already achieved without using speed feedback. The connection of power, motor and control cables to the inverter must be carried out as shown in Fig. Closed-loop Torque Control P The data, required for the thermal motor model, is estimated from the rating plate data refer to Fig.

Most Related  RYA COMPETENT CREW BOOK PDF

This means that it is possible to transfer the parameter set from drive inverter Manhal to drive inverter B which, for identical applications e. The voltage value at 0 Hz is determined from the product of rated motor current P, stator resistance P and 6se6404-2ud21-1aa1 appropriate parameters P — P Rated motor current Min: In order to carry-out the residual distance calculation on the load side, the mechanical arrangement of the axis gearbox ratio, linear or rotary axis must be appropriately parameterized refer to Fig.

A 6se6440-2ud21-1xa1 of the parameters, which are calculated, depending on the setting of P, are included in the parameter list. Vector control is being used. Page 0, it is possible that the drive is accelerated as a result of the search current!

Siemens MICROMASTER Operating Instructions Manual (Page 10 of 78)

However, when the line supply returns, motors can automatically start to run again without any operator intervention. Page NOTE If the drive inverter fan fails, this would 6se64440-2ud21-1aa1 indirectly detected by the measurement of the heatsink temperature.

Table Important Parameters For The Pid Dancer Roll Control This loop represents the difference between the material fed-in and that fed-out and therefore indicates the process quality.

Unfiltered units, all voltages and powers. This measure is important to ensure that air gaps and creep distances are observed. Page 25 No equipment that could have a negative effect on the flow of cooling air should be installed in this area.